Heat exchanger tube plugs are used to seal leaking heat exchanger tubes, preventing damage to adjacent tubes and keeping the efficiency on an aging exchanger as high as possible. Torq N' Seal® Heat Exchanger Tube Plugs by JNT Technical Services offer a fast, simple and effective way to seal leaking heat exchangers up to 7,000 psi. Whether you have a feedwater heater, lube oil cooler, condenser or any other type of heat exchanger, knowing how to properly seal a leaking tube will improve turnaround time, reduce project cost and ensure the longest possible asset life. This article will review how to properly plug a leaking heat exchanger tube.
Identifying leaks
There are several ways to identify heat exchanger tube leaks: pressure leak tests, vacuum leak tests, eddy current testing, hydrostatic testing, acoustic testing and radiotracers, to name a few. The proper method for a given heat exchanger depends on the service requirements associated with that exchanger. For instance, a critical feedwater heater often needs to be plugged based on the minimum wall thickness before a leak even occurs. For these applications, eddy current testing or acoustic testing will be the best options. On the other hand, an array of condensers with significant overcapacity can withstand a certain number of leaking tubes without affecting the process. In this case, vacuum or pressure testing are the best options for their low cost and ease of use.
Preparing for tube plugging
Now that all tube leaks (or tubes with thin walls below the minimum allowed thickness) have been identified, it is time to begin the tube plugging process. The first step is removing any loose scaling or corrosive oxides from the tube's inner diameter surface. Use a slightly oversized, hand-operated tube brush or put some emery cloth on your finger. Gently maneuver the brush or cloth inside the tube, removing any loose material. Two to three passes are enough; the goal is just to remove loose materials -- not to re-size the tube.
Confirm tube diameter and material
Next, confirm your tube size by measuring the tube inside diameter (ID) with a threepoint micrometer or standard caliper. If you use a caliper, take at least three readings, and average them together to get the effective ID. Use even more measurements for the average if you only have a ruler. Confirm the measured diameter matches the design diameter from the U-1 datasheet or heat exchanger nameplate. You should also confirm the tube material at this time. It should also be listed on the U-1 datasheet or exchanger nameplate.
Select the correct tube plug
At this point, you have identified the leaking tubes, cleaned lightly, and confirmed the size and material. Now it is time to select the correct heat exchanger tube plug:
Step 1: Take your measured tube ID and round down to the nearest ten-thousandth. Remove the preceding "0" and decimal point.
- Measured ID: 0.694 inches (3/4 inches x 22 Birmingham Wire Gauge)
- Rounded ID: 0.690 inches
- Simple ID for part number: 690
Step 2: Take your material and match it to the associated abbreviation:
- BR = copper/brass (stock material)
- CS = carbon steel (stock material)
- 316SS= 316 stainless steel (stock material)
- 1018CS = 1018 carbon steel
- F5 = A182-F5 carbon steel
- 90CN = 90/10 copper nickel
- 70CN = 70/30 copper nickel
- 304SS = 304 stainless steel
- EXAMPLE: Tube material = Copper/ Brass = BR
Step 3: Create your part number using the simple tube ID and material abbreviation:
- Part number: TNS-690-BR
Alternatively, you can contact JNT Technical Services, and one of its engineers will help specify a part number. You can also use the Plug Selector found by visiting www.torq-n-seal.com/contact-us/plug-selector.
Installing the heat exchanger tube plugs
Set your 3/8-inch-square drive torque wrench to the recommended installation torque listed on your Torq N' Seal plug box. Affix the Hex Capture Driver (supplied in every box of Torq N' Seal plugs) to the torque wrench. Then affix the Torq N' Seal plug to the Hex Capture Driver. Insert the plug into the tube so the back of the screw is even with the tubesheet face. Rotate clockwise slowly until the torque wrench clicks. Pull the Hex Capture Drive free. Your tubes are now sealed to 7,000 psi.
For more information, visit www.torq-n-seal.com, email sales@torq-n-seal.com or call (201) 641-2130.
