Properties of high-viscosity foam agents and their influence on proportioning systems

From fluorinated to fluorine-free foam agents

by

Success in firefighting depends on various factors. The most important one is the choice of the right foam agent.

In the past AFFF and AFFF-AR foam agents were most widely used. They had in common, that they used fluorine as one of the base components, as it has very good extinguishing properties. They had the advantage that a broad variety of different chemicals could be extinguished with one foam agent. 

Over the last years legislation has been passed in various countries, banning fluorine in foam agents. This means that companies must find fluorine-free replacements. These are widely available, but presently have the disadvantage that they are not drop-in replacements for the fluorinated foams. In many cases, these non-fluorinated foam agents (FFF) do not yet have approvals for the entire range of flammable substances. Accordingly, various non-fluorinated foam agents have to be used where one fluorinated product used to do the job.

Viscosity

One physical property that many of the fluorine-free foam agents have in common is an increased viscosity. High viscosity foam agents have been used in the firefighting industry for decades, such as in AFFF-AR, but with the broad transition to non-fluorinated foam agents the topic of viscosity needs to be considered more widely. The term viscosity refers to the resistance of a fluid to deformation. The higher the viscosity, the thicker, less flowable the fluid is. The lower the viscosity, the thinner, more flowable it is.

Pseudoplastic foam agents

Low viscosity foam agents, such as AFFF, Hi-Ex, Class A or multipurpose are characterized as Newtonian fluids. High viscosity foam agents, such as AFFF-AR and FFF are often pseudoplastic fluids. Pseudoplastic means that they change their viscosity depending on the speed at which they are moved. 

The viscosity of a pseudoplastic foam concentrate can be characterized as a function of dynamic viscosity and shear rate, whereby the shear rate is the rate at which a fluid is sheared or “worked” during flow, i.e. due to the friction between the fluid and the wall of the pipe work and also within the flowing liquid itself. The shear rate is also an indicator for the flow velocity of a liquid. As with individual viscosity values, a dynamic viscosity / shear rate curve is always associated with a specific temperature. 

Figure 1 shows the difference between a Newtonian and a pseudoplastic fluid. FM Approvals, as an example, has defined the shear rate range of 5 1/s to 600 1/s as relevant for foam agents and proportioning systems. 

In the following we will have a look at highly viscous foam agents in general and what to consider when deciding on a proportioning system.

Viscosity curve

The viscosity of foam agents has a major influence on the accuracy of proportioning. Highly viscous foam agents have a significantly higher pressure-loss while flowing than low-viscous foam agents do. This rules many proportioning technologies out which are based upon pressure ratios. Proportioning technologies that are suitable for high-viscous foam agents are generally such that use displacement pumps. Like foam agents, variable viscosity proportioning systems are characterized by a viscosity curve which describes the ability up to which viscosity fluids can be processed. The curve depends on the technical characteristics of the individual proportioning technology and system design. 

Air entrapment

Another major challenge when handling high-viscosity foam agents is air entrapment. In the case of high viscosity, pseudoplastic foam agents, the air bubbles, that may form during transportation or refilling can remain in the liquid and therefore have an impact on the proportioning rate. A volume of 10% entrapped air means a 10% reduction in the proportioning rate so that a nominal rate of 3% effectively becomes 2.7%.

In the following, different types of proportioning systems will be compared with regard to the effects of the transition from a Newtonian to a highly viscous, pseudoplastic foam agent.

Venturi proportioner

When using self-inducting Venturi proportioners the limiting factor for switching to a highly viscous foam agent will be the limited suction capability of the Venturi device. Suction lines will generally need a large diameter and be very short if they are to functional at all, as the suction capability of the system is only generated by the water flow. It is also to be expected that the pressure drop in the extinguishing water line will be very high. 

Bladder tank with wide range proportioner

If a bladder tank with a wide range proportioner is to be used after the conversion to FFF agents, the pressure drop in the connecting line between bladder tank and proportioner may be a limiting factor due to the friction loss. In any case, the pipework of the foam concentrate line and the Venturi orifices will need adaptation to the high viscosity of the foam agent. The use of wide range proportioners requires also enlarged suction and foam agent injection lines to allow a better flow of highly viscous foam agents and correct proportioning rates at varying flows.

Electronic proportioner

Electronic proportioners with a gear pump, in which excess foam agent is returned to the foam agent tank, will need an adaptation of the suction and foam agent injection lines. Otherwise, the system will need to be recalibrated to the properties of the higher viscous foam agent. Gear pumps generally work well with liquids of higher viscosity. However, a higher back pressure of an extinguishing system leads to foam concentrate leakage at low flow rates.

Mechanical proportioner

Proportioning systems using a water motor with a gear pump will need new pipe work to accommodate the highly viscous foam agent. In addition, the minimum and maximum water flows must be reviewed, as gear pumps have a varying amount of foam concentrate leakage dependent on the water flow and the back pressure in the extinguishing water system. High back pressures and low water flows may have an increased effect on the leakage, so the dimensions of the gear pump for the required water flows should be reviewed. 

When using a water motor driven proportioner with a piston pump, the suction line between the foam agent tank and the pump must be adapted. Otherwise, no changes need to be made, as the piston pump does not have any leakage. Suppliers of water motor driven proportioners with a piston pump use two different pump types. One of them is regular industry pumps designed for pumping low-viscosity Newtonian fluids such as water or former AFFF agents. The second type are pumps that are specifically designed for high-viscosity pseudoplastic fluids such as FFF agents. The latter generally have a significantly higher efficiency than the usual industry pumps when using high-viscosity foam agents.

FireDos GEN III water motor driven proportioning systems are exclusively equipped with piston pumps developed in-house, which are designed and tested for use with low-viscosity Newtonian and ultra-high-viscosity pseudoplastic foam agents. In addition, all systems are equipped with foam agent return lines for eco-friendly testing of the of the proportioning rate without the need to generate premix or foam.  

For all proportioning systems it should be observed that the above-mentioned viscosity curves for the proportioners and the foam agents are compatible. A changeover from a Newtonian to a high-viscosity foam concentrate is possible for almost all proportioning technologies with the right planning. The changeover must be carefully planned and carried out, and it is recommended to involve specialized companies for the changeover.

More information can be found at firedos.com

Tags

by